Good day good folks,
Last night I purchased a more advanced OBD2 reader than my plain Innova 3030 that simply reads the codes.
This one is the Innova 3130, bought it mainly for the live data reader, and the EVAP test which it now states is not even supported.
Anywho, below are my readings from today. I can't really understand much other than the pretty straight forward ones. Can anyone tell me whereabouts between each reading should typically be around, and what in my case is raising any flags, and what the issue may be?
November 22, 2013 @ 3:41PM
2004 HYUNDAI SANTA FE GLS 2.7L V6
Fuel Sys 1: CL
Fuel Sys 2: CL
Calc Load(%): 11.8
ECT(°F): 199
STFT B1(%): 3.1
LTFT B1(%): -14.8
STFT B2(%): 5.5
LTFT B2(%): -10.9
Eng RPM: 703
Veh Speed(mph): 0
Spark Adv(°): 11.5
IAT(°F): 131
MAF(lb/min): 0.3
TPS(%): 6.7
O2SLoc B1S12__ B2S12__
O2S B1 S1(V): 0.800
STFT B1 S1(%): 0.0
O2S B1 S2(V): 0.450
STFT B1 S2(%): 99.2
O2S B2 S1(V) 0.095
STFT B2 S1(%): 7.0
O2S B2 S2(V): 0.430
STFT B2 S2(%): 99.2
OBDSup: OBD2
Only thing I understand that seems off is the TPS %, it's at 6.7% when I believe it should be at 0% (gas pedal isn't being touched at all), and the highest it went when pressing the gas pedal all the way to the bottom with the car off was about 87% or so.
Any help would be greatly appreciated. Want to learn how to use and understand these readings otherwise this was a waste of $225. Want to also use it on several other vehicles but again, useless if I don't understand the readings and where they should be at.
THANKS AGAIN
Last night I purchased a more advanced OBD2 reader than my plain Innova 3030 that simply reads the codes.
This one is the Innova 3130, bought it mainly for the live data reader, and the EVAP test which it now states is not even supported.
Anywho, below are my readings from today. I can't really understand much other than the pretty straight forward ones. Can anyone tell me whereabouts between each reading should typically be around, and what in my case is raising any flags, and what the issue may be?
November 22, 2013 @ 3:41PM
2004 HYUNDAI SANTA FE GLS 2.7L V6
Fuel Sys 1: CL
Fuel Sys 2: CL
Calc Load(%): 11.8
ECT(°F): 199
STFT B1(%): 3.1
LTFT B1(%): -14.8
STFT B2(%): 5.5
LTFT B2(%): -10.9
Eng RPM: 703
Veh Speed(mph): 0
Spark Adv(°): 11.5
IAT(°F): 131
MAF(lb/min): 0.3
TPS(%): 6.7
O2SLoc B1S12__ B2S12__
O2S B1 S1(V): 0.800
STFT B1 S1(%): 0.0
O2S B1 S2(V): 0.450
STFT B1 S2(%): 99.2
O2S B2 S1(V) 0.095
STFT B2 S1(%): 7.0
O2S B2 S2(V): 0.430
STFT B2 S2(%): 99.2
OBDSup: OBD2
Only thing I understand that seems off is the TPS %, it's at 6.7% when I believe it should be at 0% (gas pedal isn't being touched at all), and the highest it went when pressing the gas pedal all the way to the bottom with the car off was about 87% or so.
Any help would be greatly appreciated. Want to learn how to use and understand these readings otherwise this was a waste of $225. Want to also use it on several other vehicles but again, useless if I don't understand the readings and where they should be at.
THANKS AGAIN